What does the header tank feed

The header tank, otherwise known as the feed and expansion tank or cistern, is an essential part of an open vented central heating system with a regular boiler. The role of the header tank is to supply water to the central heating system and also maintain the level of water, which expands when heated.

What is the purpose of a header tank?

The header tank is used to fill the heating system and accommodate the expansion of water during the heating cycle. It has an overflow pipe running to outside, a mains water supply connecting to the tank via a ball valve used to fill the system and a cold feed pipe* and an open vent pipe*.

Why is hot water feeding back into header tank?

Another frequent cause is a blockage where the feed / vent pipes from / to the F&E tank join the main pipework. That causes hot water to go up the vent into the small tank whence it is dragged back into the system again via the feed.

What does the water tank in the loft feed?

Cold water storage tanks are generally situated in the loft. They can be used to supply the hot and cold water taps on the bath. They can also act as a Feed and Expansion tank (F+E) for the heating system. Most of these tanks are fed by a ball valve on mains pressure.

What does the feed and expansion tank do?

The feed and expansion tank, header tank, or feed and expansion cistern as it is technically known, is a cistern which supplies the central heating circuit with water and accommodates the expansion of the water when it is heated by the boiler.

Why does my expansion tank keep filling up?

Not Enough Air in Diaphragm Tank The most common expansion tank problem in a diaphragm tank is losing small amounts of air through the valve. … If the tank does not hold its air pressure after you complete this fix or it fills with excess water, you may need to replace the diaphragm.

Should header tank be covered?

An insulating jacket prevents the cold water in the header tank from freezing up, and this also helps to stop pipes from freezing. … Header tank insulation is recommended if you’re having your pipes lagged for winter.

Should attic water tanks be covered?

The tank must be insulated and fitted with a dust proof lid. Pipes must be supported and lagged. There may be very good, and sometimes excessive, water pressure in the area resulting in more noise on filling. Reducing the flow into the house from the main stop cock outside might help.

Why is header tank overflowing?

There are many reasons why the header tank is overflowing: Issues with pump over run. Faulty coil in the hot water tank. Ball valve needs repairing or replacing.

Why do British houses have cold water tanks?

in the 19th century, the brits were afraid of napolean invading the UK and poisioning the water supply. therefore, they made it law that all houses had to have a water tank in their house. this is the reason why british have cold water tanks, and that our internal house water pressure is dependent on that tank.

Article first time published on

How high does a header tank need to be?

there should be a mimimum height between top of circulation pipework & header tank water level of 450mm (18″) but the more the better the system will work.

Do you need a header tank with a combi boiler?

A system boiler is a sort of combination of a conventional and a combi boiler. … However, unlike a conventional boiler, it doesn’t require a header, or cold feed, tank in the loft. A system boiler takes water from the mains supply, like a combi boiler, and heats it in the heat exchanger.

How do I stop my hot water cylinder from overflowing?

Find the PTRV valve on the side of the cylinder near the top or bottom, then lift the silver lever three or four times to open, close and clear any blockages. If the water flow comes to a stop then your problem is solved. But if it keeps running then you probably need to replace the valve.

How do I know if my expansion tank is working?

The tank should be full of air and therefore sound hollow. If it makes a dull thud rather than a hollow sound, your tank is full of water and needs repair or replacement. You can also gauge this by feeling the tank, which will be cool where it’s holding air and warm where it’s holding water.

What pressure should my expansion tank be set at?

The recommended water pressure is between 50 and 60 PSI. Thermal Expansion Tanks contain an air bladder which is pressurized with air, and expands and contracts to absorb the expanded water from the water heater. needed. Check the air pressure in the Expansion Tank using a tire gauge.

Where does an expansion tank go on a boiler?

Usually the expansion tank is mounted on the hot or supply side of the boiler and usually it’s located before any circulator pumps. If you see a tank that looks like the unit below, your boiler has an internal-bladder type hydronic heating boiler expansion tank.

Why does my cold water tank keep overflowing?

Typical cause – a faulty ball valve The most common reason for a cold water tank to overflow is a faulty ball valve. … As the water level in the cistern rises, the float pushes a washer onto the valve seating – a plastic nozzle inside the valve body. This stops the flow of water into the cistern.

Why is hot water coming out of my overflow pipe?

Hot water systems It’s also called the relief valve. Water expands when heated, pressure builds up in the tank and is released through the overflow pipe. So water dripping or running from the valve can be a sign of a normal, functioning system.

Can an expansion tank explode?

As water heats up, it can expand dramatically, and if it’s hot enough to turn into steam, this can add even more pressure to the water heater. If the relief valve is malfunctioning, this can lead to an explosion.

What happens when expansion tank fails?

Oftenthe diaphragm dividing the two systems will fail, causing the two systems to become one. When this happens, the expansion tank turns into a “dead leg” that will eventually cause damage and premature failure to your water heater.

What size expansion tank is needed for a 50 gallon water heater?

For a 50-gallon water heater, you require a 2-gallon expansion tank. Depending on how high your water pressure is, however, you may need to go up a size to a 4.5-gallon expansion tank.

Why is my heating system pumping over?

Pumping over refers to a symptom of an improperly configured central heating system in which water is discharged into the feed and expansion cistern via the expansion pipe while the pump is running. The cause is usually either: … The pump’s speed is too high.

Is a leaking overflow pipe an emergency?

But the valve only flows when there is a problem in the system. So, if you see this valve leaking, you should immediately take notice. The pipe might leak because of excessive pressure to the system or because of issues with the pressure valve. In both cases, it is highly advised to call professionals for service.

Why do I need a cold water tank in the loft?

Why are there two water tanks in your loft? If you are not sure why there are two water tanks in your loft, it is probably because the property has (or used to have) a vented central heating system. Water from the mains is fed into the larger of the tanks which is the cold water storage tank.

How full should water tank be?

Follow the Overflow Tube If you can’t find a water line mark, the correct height for the water is about 1 inch below the top of the hollow overflow tube located around the middle of the tank. The water level cannot be above this tube, or it will constantly overflow down into the bowl.

How long does attic water tank last?

So, the house where the attic water tank needs replacement is usually around 30 years or more. Two: Think about it, these older generation water tanks are made of a form of metal, galvanised iron in fact. And over time immersed in water it will disintegrate and the chemicals and materials will seep into your water.

How do you clean an attic water tank?

1. Step 1: Inspection. Landlords or letting agents should inspect cold water storage tanks at least once a year as part of their Legionella risk assessment or monitoring procedures. …
2. Step 2 – Drain the tank. …
3. Step 3 – Scrub the tank. …
4. Step 4 – Refill the tank.

Why does England have 2 taps?

“This tradition dates back to a time when hot and cold water were kept separate to prevent contamination through cross connection,” he said. … “This caused an imbalance of pressures which meant that if incorrect taps and valves were installed one stream of water could force its way across to the other.”

Where should water tank be in house?

The location of the tank should be towards the northeast direction of the Plot. Consider building your tank towards the north and east direction. When placed in the northeast, the tank can bring in happiness, wealth, and prosperity to your home.

Can you drink water from a cold water storage tank?

Is stored water safe to drink? … Ideally you should only use a tap connected to the mains water supply for drinking, food preparation or teeth cleaning; however if your drinking water comes from a storage tank then it will be safe to use if the tank is properly designed, correctly installed and kept in good condition.

What head of water gives 1 bar pressure?

olive, an approximate guide is each meter of head height (that is the top level of water in the tank down to the Taps etc in the House) developes 0.2 Bar, so 5 mtrs of head height would give you 1 Bar of pressure, hope this helps.